Bitte benutzen Sie diese Referenz, um auf diese Ressource zu verweisen: doi:10.22028/D291-22857
Titel: Strömungssimulation der Füllung einer Druckgussform mit Alumosilikatsuspensionen
VerfasserIn: Legrix, Jean-Christophe
Sprache: Deutsch
Erscheinungsjahr: 2012
Kontrollierte Schlagwörter: Thixotropie
Rheologie
Numerische Strömungssimulation
Gießen <Urformen>
Sanitärkeramik
Schlickerware
Kaolin
Kontinuumsmechanik
Freie Schlagwörter: Materialmodell
CFD
casting
sanitary ware
thixotropy
rheology
materialmodell
DDC-Sachgruppe: 620 Ingenieurwissenschaften und Maschinenbau
Dokumenttyp: Dissertation
Abstract: Das keramische Druckgussverfahren wird in der Sanitärindustrie erst seit den 1980er Jahren verwendet und ist somit ein noch relativ junges Verfahren mit viel Optimierungspotential. Insbesondere der Füllvorgang einer Druckgussform wurde bis heute nur wenig untersucht. Die Optimierung des Füllvorgangs kann geometrischer Art sein (Design des Produktes, Eingussposition und Entlüftungsposition) oder durch die Anpassung der Prozessparameter (Formmaterial, Druck, Füllgeschwindigkeit und Temperatur) und der rheologischen Eigenschaften der keramischen Gießmasse (Viskositat, Thixotropie und Litergewicht) erfolgen. Diese Vielfalt an Parametern zur Steuerung des Druckgussprozesses sowie die Tatsache, dass experimentelle Messungen in einer Druckgussform während des Füllvorgangs so gut wie unmöglich sind, machen den Einsatz einer Computersimulation notwendig. Dies zu ermöglichen ist das Ziel dieser Arbeit. Zunächst wird ein phänomenologisches Materialmodell präsentiert, das sich zur Beschreibung des thixotropen Verhaltens von Alumosilikatsuspensionen eignet. Anschließend wird das Materialmodell in die Strömungssimulationssoftware FLOW3D implementiert und anhand von einfachen zweidimensionalen Geometrien sowie an einer produktionserprobten, komplexen dreidimensionalen Geometrie validiert. Das Ergebnis dieser Arbeit trägt zum besseren Verständnis des Füllvorgangs einer Druckgussform bei und stellt der Sanitärindustrie, in Kombination mit der vorhandenen praktischen Erfahrung, ein sehr wirksames Werkzeug zur Optimierung des Druckgussprozesses zur Verfügung.
The pressure casting process has been introduced in the sanitary ware industry since the 1980s and is therefore still a young technology with a high potential of optimization. Especially the filling of a pressure casting mould has been analysed poorly until today. The filling of a sanitary mould is controlled through many different parameters like geometry parameters (product design, inlet position, inlet diameter, etc), process parameters (mould material, pressure in the mould, inlet velocity, temperature, etc) and material properties of ceramic slurry (viscosity, thixotropy, density, etc). The correct setting of the above listed parameters is extremely difficult, due to their influence on the filling which can not be measured directly. To better understand which influence the different parameters have on the filling of a pressure casting mould as well as to rapidly solve problems in the production, it appears necessary to use the computational fluid dynamics. This is the main objective of this thesis. In a first step a macroscopic material model, able to describe the thixotropic behaviour of ceramic slurry, will be developed. Then the material model will be implemented in the commercial computational fluid dynamics software FLOW3D. Computer simulation of 2D-geometries and 3D-geometries will be used to validate the material model and the move of the slurry surface during the filling of a pressure casting mould. The results of this thesis illustrate that the computer simulation of the filling of a sanitary mould, with a thixotropic slurry, help to better comprehend the filling process of pressure casting in the sanitary industry. In combination with the industrial practical experience about pressure casting, the computer simulation will be a very efficient tool to rapidly master casting production challenges.
Link zu diesem Datensatz: urn:nbn:de:bsz:291-scidok-50690
hdl:20.500.11880/22913
http://dx.doi.org/10.22028/D291-22857
Erstgutachter: Diebels, Stefan
Tag der mündlichen Prüfung: 16-Jul-2012
Datum des Eintrags: 13-Feb-2013
Fakultät: NT - Naturwissenschaftlich- Technische Fakultät
Fachrichtung: NT - Materialwissenschaft und Werkstofftechnik
Ehemalige Fachrichtung: bis SS 2016: Fachrichtung 8.4 - Werkstoffwissenschaften
Sammlung:SciDok - Der Wissenschaftsserver der Universität des Saarlandes

Dateien zu diesem Datensatz:
Datei Beschreibung GrößeFormat 
diss_jcl.pdf4,01 MBAdobe PDFÖffnen/Anzeigen


Alle Ressourcen in diesem Repository sind urheberrechtlich geschützt.